PN0108 8-Port Power Over the NET™

Overview

Altusen’s PN0108 is equipped with eight hotpluggable ports for easy server room management. Each port can be individually controlled so that users can set the power on sequence and delay time for each port to allow equipment to be turned on in the proper order.

Compare Product
Category:
  • Altusen's PN0108 is equipped with eight hotpluggable ports for easy server room management. Each port can be individually controlled so that users can set the power on sequence and delay time for each port to allow equipment to be turned on in the proper order. On/Off scheduling allows for preset start/shutdowns/restarts on a daily, weekly,monthly basis.The PN0108 is the most convenient, reliable and cost effective way to obtain access to your server room remotely.*

    • Remote power on / off / reboot control for eight outlets via TCP/IP and a built in RS-232 PON (Power Over the NET™) port

    • Local power on / off / reboot control via the PN0108's PON port to the computer's RS-232 port

    • Daisy chain up to 15 additional stations to control up to 128 outlets

    • Manual switching between Local and Remote access for each port via front panel push button switches

    • Individual control of each port - users can set the power on sequence and delay time for each port to allow equipment to be turned on in the
    proper order

    • Easy setup and operation via a GUI interface

    • Provides three configuration/management methods: Browser; Telnet; or Console Terminal

    • Safe shutdown and rebooting for Windows systems*

    • Overcurrent protection and recovery for each AC port (110 V model only); total port overcurrent protection (both models) - remote users can
    monitor the outlet status via the GUI interface

    • Separate circuits for the unit's power and the power to the devices - the power control status menu is still accessible even when an overcurrent
    condition trips the devices' circuit breaker

    • On/Off scheduling - allows everything from a one-time start/shutdown, to daily, weekly, etc. starts/shutdowns at user-specified times

    • Port grouping - perform the same action on a specified group of ports

    • LEDs for easy status monitoring

    • Two level (Administrator and User) security

    • Configuration can be reset

    • Firmware upgradeable - daisy chained stations receive the upgrade via the daisy chain bus

    • UL/TUV approved

    • Multiplatform support: Windows 2000/XP/Vista, Linux, Unix and FreeBSD.

    *Safe shutdown and rebooting is supported if the Power Monitor utility has been installed
    *The PN0108 is not a stand-alone unit. It must be connected to the CN6000, PN9108, SN0108 or SN0116 to access these features

Power Inlets

1 x IEC 60320/C14 Male

Power Outlets

8 x IEC 60320/C13 Female

Connectors

PON In 1 x DB-9 Female (Black)
PON Out 1 x DB-9 Male (Black)
Safe Shutdown 8 x 6-pin Safe Shutdown Jacks Female (Black)

Switches

Reset 1 x Semi-Recessed Pushbutton
Power 1 x Rocker
Firmware Upgrade 1 x Slide
Outlet On/Off 8 x Pushbutton
Remote On/Off 8 x Pushbutton

LEDs

Power Outlets 8 (Orange)
Remote 8 (Green)
Station ID 2 x 7 segment (Orange)
Maximum Input Power Rating 100 ~ 120V, 50/60Hz,12A
220 ~ 240V, 50/60Hz,10A

Power Consumption

No Load 120V/15W; 230V/15W
Max Load 120V/1440W; 230V/2300W

Environmental

Operating Temperature 0 ~ 40?C
Storage Temperature -20 ~ 60?C
Humidity 0 ~ 80% RH ,Non-condensing

Physical Properties

Housing Metal
Weight 3.70 kg ( 8.15 lb )
Dimensions (L x W x H) 43.72 x 21.83 x 4.40 cm
(17.21 x 8.59 x 1.73 in.)

 

* The specification and pictures are subject to change without notice.
* All trademarks and logos are the properties of their respective holders.

 

TOP